O-ring Not reusable Bolt Starter motor front cover O-ring Not reusable. The terms of this agreement shall be enforceable by any court of competent jurisdiction. Bolt Hose clamp Exhaust chamber assembly Rubber joint Slide the water lock to back Outer exhaust joint Inner exhaust joint 4-13. Check the excessive play of the han- dlebar. Fully close the carburetor throttle valves. Checking steps: Connect the tester leads between the starter relay terminals as shown. Once you download your manual it is yours forever.
Copyrights and Trademarks belong to their respective companies. If a and b length are not even, adjust the cable joint. White paint mark a is for No. Armature coil continuity: Commutator segments 1 Continuity Segment - Laminations 2 No continuity Segment - Armature shaft No continuity Brush holder inspection 1. There are no incorrect wiring connections. Connect the cable joint and tighten the locknut. Filling steps: Remove each filler cap.
Bolt Damper Bolt Engine mount Reverse the removal steps for installation. Piston pin and bearing inspection 1. ©Copyright 2019 Short Block Technologies, Inc. It has been written to suit the needs of persons who have a basic understanding of the. Flywheel magneto removal and installation 1.
Do not smoke while handling gasoline petrol and keep it away from heat, sparks, and open flames. Dowel pin When installing the jet pump unit, align the drive shaft spline male with the intermediate drive shaft spline female. Make sure the oil symbol 4 and. These terms are an essential part of the bargain between the parties based upon the price of sale negotiated herein. The foregoing are the Buyer's exclusive remedies.
The vast majority of sellers offering manuals online have little to no experience in the service industry whatsoever. It is a sealed unit and if it is faulty it must be replaced. There is no special software required to download the manual and start viewing it, as all computers, tablets and readers are already installed with the necessary software from the manufacture to download and view the digital book. Brass insert nut 1 Hull 2 Urethane foam 3 Silicone sealant 4 Graphic removal. Clean parts with compressed air when disassembling. I got my answers right away.
Fill: Intermediate housing Recommended grease: Yamaha marine grease, Yamaha grease A. Remove the jumper lead 2 from the green two-pin connector. In the event that an engine with a two 2 year warranty is purchased, all the same guidelines apply with the exception of the term. Measure nozzle deflector length a and b. Said mediation shall be conducted by a certified mediator under the laws of the state of Florida, and each party shall be responsible for paying an equal share of all mediation costs. Recommended grease: Yamaha marine grease, Yamaha grease A Water resistant grease 7.
Check the each throttle valve is fully closed a. If a good spark is obtained, the problem is not with the ignition system, but possibly with the spark plug s or another compo-. This manual will help you save money upwards into the thousands. First, apply tape 1 to the inner surface of the hull and then laminate fiberglass mats over the tape with resin. To prevent water from entering the ure- thane foam, apply silicone sealant to the inside of the hole as shown. Non-reusable items Always use new gaskets, packings, O- rings, oil seals, split-pins, circlips, etc.
Always follow these preventive mea- sures: Charge batteries in a well-ventilated area. Inspect the oil pump hoses for proper routing and make sure there are no restrictions in the line. Bolt Mount bracket 1 Bolt Mount bracket 2. I expected a few days for a response, not minutes. Adjust the oil pump cable so that the mark a on the oil pump lever is aligned with the mark b on the oil pump body. Sand the scratches with 400 grit sand- paper either wet or dry until the scratches are smooth. Checking steps: Loosen the throttle stop screw 1 until untouched the screw end from the throttle lever.
Then, sand the scratches once again with 600 grit sand- paper either wet or dry. Bolt Exhaust chamber assembly Outer exhaust joint Inner exhaust joint Reverse the removal steps for installation. Make sure the battery leads are con- nected properly. The information has been compiled to provide the mechanic with an easy to read, handy refer- ence that contains comprehensive explanations of all disassembly, repair, assembly, and inspection operations. Thank you ever so much for your fast replies, excellent products, and perfect service. Will definitely recommend to friends. Inspection steps: Remove the water inlet cover 1.
It is fully printable, print 1 page, 1 chapter or print the entire manual and put it in a 3-ring binder. Bolt Bow eye Rope hole fitting Spout Bolt 8-42. Install: Choke cable 1 Throttle cable 2 Choke cable guide installation position a: 13—15 mm 0. Stay Reverse the removal steps for installation. I've also owned a small independent repair shop, so I understand your time is your money.