Apply a few drops of Loctite 243 Blue to the threads of the upper front bearing housing screw removed in Step 6. Changing the fluid requires some special equipment and procedure so it's best left to the toyota dealer on this one. Remove and discard the socket head cap screw 2 that fastens the oil spout assembly to the transmission housing. Working on or near the exhaust system when the engine is hot could result in severe burns. Tighten to 84- 108 in-lbs 9.
Tighten the screw to 84-132 in-lbs 9. Tighten to 84-108 in-lbs 9. Transmission top cover screw 4 2. Refer to Service Manual for instructions. Lower front bearing housing screw Figure 1. Remove the upper front bearing housing screw 3 from the side of the transmission case.
Repair guides will give you a decent overview of the way to identify a problem and, if possible, to fix it yourself. It is always worth having to hand a service manual that you can read through as a diagnostic step if you find that you are having some problems with your Toyota. Tighten to 84- 108 in-lbs 9. Download manual guide of Corolla Fielder Owners Manual Pdf in pdf that we listed in Manual Guide. This site consists of a compilation of public information available on the internet.
Replace oil after every subsequent 5000-8000 Km. Install four chrome hex socket head screws 4 and washers 2 on transmission side cover 5. Transmission top cover screw 4 2. Position the top interface cover over the transmission top cover. Tighten the screw to 84-132 in-lbs 9. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. Even for peace of mind, it is useful to have a service manual to refer to.
Disconnect battery cable, negative - cable only. Requires inspection after every subsequent 40,000 Km under normal conditions and 25000 Km under severe conditions. Upper bearing housing screw 2 Figure 1. Dec 14, 2013 P1589 Use a scan tool or Techstream and calibrate deceleration sensor. Remove and retain the three socket head cap screws 1 that fasten the right side and left front corner of the transmission cover. Install the new oil seal into the large end of the seal adapter.
Their cars are safe and reliable, and they have also risen to the top of the hybrid car market with their Lexus machine. The download is free, too, which will save you a considerable amount of money in time. Where Can I Get A Toyota Service Manual? Remove the two rear bearing housing screws 2 from the side of the transmission case. Obtain the chrome lower side interface cover 1 , one 10-24 socket head screw 8 and one chrome flat washer 9 from the kit. Position the top interface cover over the transmission top cover. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole.
With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. Install ring seat tool and spring to counter shaft and new countershaft gear. Remove and discard the socket head cap screw 2 that fastens the oil spout assembly to the transmission housing. Apply a few drops of Loctite® 243 Blue to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Install six chrome hex socket head screws 1 and washers 2 on top transmission cover 3. The sealing lip should be facing down. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover.
Apply a few drops of Loctite® 243 Blue to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Posted on Aug 21, 2011 - Engine oil change: Engine oil- fully synthetic. The adapter plate should now be installed onto the Atlas transfer case. To be replaced with new reverse gear transmission bearing housing Trap Door. Lubricate the filler neck gasket with soapy water to aid in installation. Remove and retain the four socket head cap screws 1 that fasten the front and right side of the transmission cover.