Principle of operation: Install a separated chamber on cylinder head, and suck the blow-by gas to the fuel vapor separator by engine vacuum. Service Limit: Refer to page 2 Inspect the camshaft bearing for looseness or wear out. Apply with specified grease to lubricate the inside of sliding driven face. Brake Trouble Diagnosis Disc Brake Soft brake lever Uneven brake 1. Cooling fan Hold the flywheel with the universal fixture. Remove the brake fluid hose clipper or cable guide on the left cushion.
If so, replace valve guide. This entry was posted in and tagged , on by. There are 4 floor panel mounting bolts. Cam chain plate Remove cylinder. Emission Control System Positive Crankcase Ventilation System P. Install the float valve, float, and float pin. In the contact surface has any damage.
Check Remove the 4P coupler of the alternator. Free play: 10~20mm Adjust the free play by turning the front brake adjustment nut if necessary. Remove the luggage box Bolt× 4, Nut×1. Body Cover Front Cover Removal Remove the mounting screws 2 screws of front cover from the front inner cover side. Measure the radical clearance of the big end at the vertical directions. Replace it with new one if dirt or damaged. The problem is that once you have gotten your nifty new product, the sym sangyang mio 50 mio100 workshop manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging.
In case of being spread, flush with great quantity of water immediately, and then send to hospital. This entry was posted in and tagged , on by. Install the piston ring onto piston carefully. Take out the bearing spacer and then remove the Dust seal Bearing other bearing. Use vacuum cleaner or other authorized tool instead.
Throttle Valve Operation Have a wide open of throttle valve as handle bar in 2~6 mm any position and release it to let back original full closed position. Refer to chapter 5 6-17. Caution Float valve In case of worn out or dirt, the float valve and. Remove the battery negative - cable. Fuel System 2 screws Air Cut-off Valve Removal Removal the throttle cable seat screws x 2 Remove the screws screw x 2 of the air cut-off valve and its cover. Remove front brake caliper disk brake type. Installation Apply a thin coat of grease to the brake cam and the anchor pin.
Also check if the Clearance outer collar is tightly connected to the wheel hub. General Information Symbols and Marks····························1-1 Torque Values ···································· 1-11 General Safety ····································1-2 Troubles Diagnosis···························· 1-13 Service Precautions ···························1-3 Lubrication Points ····························· 1-17 Specifications ·····································1-9 Symbols and Marks Symbols and marks are used in this manual to indicate what and where the special service are needed, in case supplemental information is procedures needed for these symbols and marks, explanations will be added to the text instead of using the symbols or marks. Remove the 22mm anti-loosen mounting nut and Mounting nut gasket. Pull out the bulb and replace it with new one. Measure cylinder head wrap age with a straightedge and flat feeler gauge. Please see standard values for not listed in the table. Electrical Equipment Bulbs Replacement of Rear Winker Light Remove the rear winker light lens screws.
Fuel System Removal of Air Cleaner Open the seat. Body Cover Front Inner Cover 1 screw Removal Remove the front cover and the front under spoiler. Take out the bearing spacer and then remove the other bearing. Driving belt worn out or deformation 2. Caution Do not damage the cam chain as installing the crankshaft.
·················································· 17-5 Control System···································· 17-1 Inspection Items··································· 17-6 Fuel Evaporative Emission Control System Countermeasure for Emission Pollutants E. The troubles usually can be determinate or by performing cylinder compression test and judging the abnormal noise generated. The bearing should be turn smoothly. Snap ring Clutch block Check if shock absorption rubber is damage or Shock absorption. Remove the lower-end cone bearing seat on the frame with a punch.
Service limit: Replace when it is more than 0. Brake Inspection Check the master cylinder for damage or scratch. With a bracket to support the engine to prevent from it damage by falling down as removing the engine. General Information Do not let the wire harness contact with rotating, Protect wires or wire harnesses with electrical moving or vibrating components as routing the tape or tube if they contact a sharp edge or harness. Construction Flesh air Fuel vapor separator Blow-by pipe Exhaust pipe Carburetor Air filter Crankcase Cylinder head Flesh air Mixture gas Blow-by Engine oil Piston 2. Caution Do not bend or twist throttle valve cable. Sym Mio 50 Technical Information Type of Bike: Scooter Year: 2008 Engine Capacity: 49.
This manual contains service, repair procedures, assembling, disassembling, wiring diagrams and everything you need to know. Couplers Remove the handle rear cover rear side screw 1 screw. All marks on the piston rings must be forwarded to up side. Remove the luggage box chapter 12. This entry was posted in and tagged , on by. Camshaft Inspection Inspect cam lobe height for damaged.