Poulan p3314 manual. P3314 Poulan Chainsaw Parts & Repair Help 2019-03-10

Poulan p3314 manual Rating: 9,8/10 382 reviews

Poulan P3314 Chainsaw Troubleshooting

poulan p3314 manual

There also appears to be a fitting on the front end. Contactingtheguidebartipwithanyobject should be avoided; tip contact may cause the guide bar to movesuddenlyupwardandbackward,whichmaycausese- rious injury. There is a small, rotten piece of tubing coming from the back end of the tank. You may need to pull the starter rope up to 20 times or so to get the cylinder to clear and the saw to start. The air will pass through the cylinder and out the exhaust, carrying the excess fuel with it. Summary of the content on the page No. If the first method doesn't work then you will need to try the following.

Next

Poulan Gas Chain Saw

poulan p3314 manual

I would have thought the engine might have still run whether or not there was a filter connected. Allow the filter to completely air dry. Insert the new fuel filter. I only found out about it when the saw through the chain off the bar. Summaries Below you will find previews of the content of the user manuals presented on the following pages to Poulan P3314. You will simply turn the saw on and pull the start rope. When you remove the cover you may see a lot of saw dust and oil all packed inside.

Next

Poulan P3314 user manual

poulan p3314 manual

Secure hair above S Haveallchainsawserviceper Summary of the content on the page No. Yeah, I don't really know how it happened! Do not cut if branches arehigherthanyourshoulder. How did you do it? Replace the cap and retainer. Once the chain is tensioned, you will need totighten bar nuts. Install bar nuts and finger tighten only. I would just get another saw and keep that one for parts.

Next

Poulan P3314 Chainsaw Parts List

poulan p3314 manual

The saw will run very smokey for a bit but that will clear up as the oil is burned out of the exhaust. This will bind up saw so you can remove the clutch. Do not allow the moving chaintocontactanyotherbranches orobjects Firstcuton co Summary of the content on the page No. The Poulan 3314 chainsaw has a 14 inch bar and chain which can cut logs up to 28 inches in diameter. Remove air filter cover and air filter. An automatic chain oiler, super clean air filter system, and primer bulb for easy starting are standard, which make this model both convenient and cost-effective. If you run the saw at full must be disengaged.

Next

Poulan P3314

poulan p3314 manual

This chainsaw comes fully assembled and is protected by a 1-year warranty. There are a couple of things you can try to get your flooded saw started. I would suspect that the saw is now flooded. To replace the spark plug, remove the three screws on the cylinder cover. Slowly pull on the starter rope while blowing air into the cylinder. Use the screwdriver end of the bar tool to ensure all links are in bar groove. I'm trying to find a part that I don't know the name of.

Next

Poulan P3314 user manual

poulan p3314 manual

Now with the throttle still open attempt to start the saw. Be careful because there is a bushing with needle bearings. Always usetwohands when operatingthechain saw. The spark plug will likely be very wet with gas. My problem is rather severe.

Next

Poulan P3314 (Type 2)

poulan p3314 manual

Pull the starter rope sharply with your right handuntiltheengine starts. Gas lines seem Ok and fitted well onto carb. Beextremelycautiouswith 6inches 15 cm indiameter or larger partially fallen trees that may be poorly Thenotchmethodisusedtofelllargetrees. Reinstall air filter and air filter cover. Refill the tank with the correct fuel mixture.

Next

P3314 Poulan Chainsaw Parts & Repair Help

poulan p3314 manual

I hope this helps with your repair! Reinstall cylinder cover and 3 screws. If problems arise when using the P3314, troubleshooting steps should be taken to identify the cause of the issue. The oil pump is right there and is simply removed with one screw. Or just try to clean it out but I have been through this and it worked for about ten minutes and I ended up just replacing the pump and works fine now. Pull the spark plug and feed a piece of rope into the cylinder. Right Foot ThroughRear Handle 7.

Next