For best results, remember the following tips: Be sure that the device cable is securely connected to the correct jack Summary of the content on the page No. Move the switch cover back so it rests on the display. Nothing herein should be construed as constituting an additional warranty. When the Sound window opens, click the Sounds tab. Lift up on the right side of the system boar d until it is at approximately a 45-degree angle 2.
The display hinges are available in th e Display Hinge Kit, spare part number 574556. Turn the switch cov e r upside down with the front toward you. Flex the bottom 1 of the display panel and release the displa y hinges. Remove the backlight frame from the display panel. It provides comprehensive information on identifying computer features, compon ents, and spare parts; troubleshooting computer p. Slide the keyboard 2 back until the keyboard connector on the system board is accessible. Nav igating and sel ecting in t he Setup Utility Because the Setup Utility is not Window s based, it does not suppor t th.
Follow the local laws and regulations in yo ur area for computer battery disposal. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. To prevent damage to the connectors: Use minimal force to insert an ExpressCard. Slide your finger to the left to decrease volume and to the right to increase volume. Make special note of each sc. Restart the computer if you are prompted to do so. Remove the display panel frame 2 from the display panel.
If it is necessary to replace the display bezel or any of the display assembly internal components, remove the following screw covers and scre ws: Two ru bber screw covers on the display bezel bottom edge 1. Nothing herein should be constru Summary of the content on the page No. Reverse this procedure to in. Disconnect the modem module cable 1 from the modem module. Component Description 1 Internal microphones 2 Record sound. The edge of the module opposite the slot rises aw ay from the computer. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the g.
Reverse this procedure to install the speaker assembly. . Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel until the bezel dise. . Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
Turn the computer upsid e down, with the front toward you. Turn the computer righ t-side up, with the front toward you. To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. Remove the display panel assembly 2 from the display enclosure. The battery release la tch automatically locks the battery into place. Do not move or transport the computer when an ExpressCard is in use. If you are unsure whether the comp uter is off or in Hiberna tion, turn the comp.
Intel, Celeron, Core, and Pentium are trademarks of Intel Corporation in the U. You should hear sound through the speakers or through connected headphones. If you are unsure whether the comp uter is off or in Hiberna tion, turn the computer on, and then shut it down th. If you are unsu re whether the computer is off or in Hibernation, turn the computer on, and then shut it down thro ugh the op erating system. To reduce the possibility of heat-relatedinjuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents.
. Release the Bluetooth module 2 as far from the top cover as th e Bluetooth module cable allows. The information contained herein is subject to change without notice. The display rubber screw co. Before removing the hard drive, follow these steps: 1. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. The information contained herein is subject to change without notice.
Remove the power button b oard 2 and cable. Do not allow ano t her hard surfac e, such as an adj oining optional pr i nter , or a so. Gently slide the card into the Digital Media Slot until the card is seated. Reverse this procedure to install the top cover. Micr osoft and Windows are U.
To stop or remove a digital card: Close all files and applications that are associated with the digital card. If you are unsure whether the comp uter is off or in. . . . Remove the display hinges 2. Remove the system b oard by sliding it to the right out of the base enc.