Panasonic 5500 projector manual. Panasonic Projector Product Database 2019-01-29

Panasonic 5500 projector manual Rating: 9,4/10 339 reviews

SOLVED: Panasonic PT

panasonic 5500 projector manual

They are also used to enter the password when the password for service personnel needs to be entered. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. See page 58 for further details. It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

Next

PT

panasonic 5500 projector manual

With remote, point at is corectly and push power 1 sec or as soon as you see green light come on. To display test patterns, follow the steps below. If so, there is a chance that it wasn't installed properly or ambient temperature sensor quit before you replace the lamp. Do not insert any foreign objects into the projector. If you haven't, start with inspecting the lamp and housing. See any molten plastic inside of lamp compartment? However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Have you replaced the lamp recently? Please turn the power on again after a while.

Next

PT

panasonic 5500 projector manual

Please, give me some more description. . The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. The leveling feet at the front left and right can be adjusted. The power indicator lights up red, and the projector is placed in the standby mode. If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or. For instructions on how to install the lenses, refer to page 21.

Next

Panasonic Projectors

panasonic 5500 projector manual

In this case projector doing the same behave just like your projector. Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector operation. If so, there is a chance that it wasn't installed properly or ambient temperature sensor quit before you replace the lamp. Ask an Authorized Service Centre to clean inside the projector at least once a year. When using the projector at high altitudes 1 400 to 2 700 m , the upper limit for the ambient temperature drops by 5 °C. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. Please, give me some more description.

Next

Panasonic PT

panasonic 5500 projector manual

Level-adjusting feet page 22 Use these feet to adjust the tilt of the projector. Replacement of the lamp unit should only be carried out by a qualified technician. Remote control receiver window rear page 14 This also receives the signal beam coming from the remote control. Precautions on lamp unit replacement Remove the power plug and confirm that the surroundings of the lamp unit have cooled off. The guarantee will not be valid for any malfunctions caused by such actions. Do not reverse engineer, change or modify the software. Dust or dirt may cause defective contact.

Next

PANASONIC PT

panasonic 5500 projector manual

Button to update time zone setting Button to update time and date. These lamps flash or light up to indicate a problem. If signals with a Note number of display dots differing from the data listed above are supplied, they will be converted into signals with 1 024 x 768 dots and displayed. Be careful when handling a light source lamp. Numeric 0-9 buttons In a system that uses a multiple number of projectors, these buttons serve to specify a particular projector.

Next

Panasonic PT

panasonic 5500 projector manual

Note that these values change according to the lens used. See any molten plastic inside of lamp compartment? Advertisement Print version Many people prefer to read the documents not on the screen, but in the printed version. However,the greater the correction amount,the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. If you haven't, start with inspecting the lamp and housing. These signals support the frame lock function.

Next

SOLVED: Panasonic PT

panasonic 5500 projector manual

Contact the dealer where you bought the projector to have the battery changed. Turn the power off and follow the steps below. If this fails you can wait 4 hours and repeat. Let me know if this worked. Have you replaced the lamp recently? Steps completed within 10 minutes. .

Next