Basic data Item Standard Service Limit Length of starting carbon brush 12. I have for sale my sinnis apache 125cc de-restricted supermoto. Turn signal lamp is still off after short circuit. This motorcycle is also equipped with a two-cylinder four-stroke in-line engine with a liquid cooling system of 649 cubic meters. Remove lead-wire connector of trigger. Check if headlamp switch Replace bulb.
If one of the clutch springs, discs or plates does not work, you shall replace them in pairs. Four-pawl bush Use a special tool to screw off clutch locknut. Measure the connecting rod big end clearance along X-Y Measuring position of C. The brand was able to attract attention to itself in the international arena through participation in sports competitions. Remove bearing on right crankcase. Diagnosis procedures Electric horn mutes. This kind of power lock has electromagnetic anti-theft function.
Remove bracket for the rear brake lever. Set throttle handle to its full open position and kick start the engine. During engine oil pump removal and installation, pay attention not to drop anything into the crankcase. Attention Gas exhausted from the motorcycle contains harmful carbon monoxide, which may lead to loss of consciousness and death. If they cannot meet the specified value, replace the drive chain. If needle valve seat is worn, the main carburetor body shall be replaced. If there is bearing clearance in the wheel hub or rotation of the wheel is unbalanced, replace it with a new one.
Turn on ignition switch; press horn button or slide turn on signal lamp switch. Measure braking shoe and brake disc and record the maximum values. Manual Keeway Superlight 2019 can be very useful guide, and Manual Keeway Superlight 2019 play an important role in your products. Power lock assembly 7 Voltage regulator. Tester Vernier caliper Measure shift fork thickness. Keep both sprocket and drive chain in good conditions, or newly replaced chain or sprocket will be worn soon.
The first motorcycles appeared in 2000, and the quad bikes in 2004. Battery is low or the wire from battery Power supply from battery is normal. Use of special tools can realize safe, reliable and quick disassembly or assembly of components, as well as working efficiency improvement and labor saving. The problem is that once you have gotten your nifty new product, the Manual Keeway Superlight 2019 gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. In addition, it is equipped with an electric starter, an exhaust pipe made of stainless steel, wide 18-inch tires, a faceted reflector on the front headlight, stylish oval rearview mirrors, high-strength shock absorbers and a multifunctional instrument panel. Measure carbon brush length Service limit: replace it when it is shorter than 8. All the plastic connectors have pawls on them.
Motors of their own design began to be manufactured in 1996. If a battery is laid aside after discharging, its service life will be shortened and its performance is degraded. Start the engine and run the engine on idle for a few minutes. While installation, tighten bolt and nut to their specified torque. During positive lead wire disconnection, be sure to prevent the tools being used from touching the frame;. Higher idle speed Unsteady idle speed Pull throttle valve of carburetor by hand Use an ignition timing lamp to Check compression pressure in cylinder and see if it is completely closed. Distortion and injury may affect operation of cables.
Release the pawl from frame and remove seat cushion 1. Turn signal lamp is not lit or dim. Front fork bent, front wheel shaft bent. Screw off the two locknuts and remove the lock washer, cam shaft and C-type gasket. Length limit of 10 chain links is 127mm. Remove throttle handle and bolts.
Check if clearance of clutch handle bar is Check if gearshift box is distorted and shift lever is deformed or over worn. Turn signal lamp is bright. Table 1-39 Name Remarks Multimeter Figure 1-41 Ignition tester Figure 1-42 Continued Table 1-40 Figure 1-41 Figure 1-42. If they are, replace them. Frame 1461986, engine 353 Feky 120028-6.
At first it was based in the garage of one of the founders, and only when things went uphill, moved to the production room. Screw off the three cap nuts and Tester hexagon nuts, remove cylinder head. Never run the engine in an enclosed place. Remove the battery from the battery case 1. Correctly install jaw of each part during combination. Check if bearing of wheels are over worn or injured;. Preparatory data include attentions that shall be paid on all the maintenance operations in the Instruction and Maintenance Manual.