Jcb 3dx backhoe parts manual. JCB SERVICE MANUAL 2019-01-26

Jcb 3dx backhoe parts manual Rating: 7,6/10 357 reviews

JCB 3DX Backhoe Loader Parts Catalogue Manual

jcb 3dx backhoe parts manual

Otherwise we will assume you are happy to continue. Do not use a machine which is due for a service. With the tester unit installed in place of the hammer, measure the circuit oil flows, back pressure and pressure relief setting. Charge for 60 to 72 hrs. Note: The eight screws A thread directly into the body of the Hammermaster, four on each side. Note that tool bushings tend to wear oval as shown. Remove loader end attachment such as a shovel if fitted.

Next

Reading : Jcb 3dx Backhoe Parts Manual

jcb 3dx backhoe parts manual

If two or more people are working on the machine, make sure each is aware of what the others are doing. The repeated swallowing of very small quantities can cause chronic lead poisoning. Note: If a new belt is fitted, the belt tension must be checked again after the first 20 hours of operation. Lift valve body A away from cylinder H. Remove the kingpost bottom pivot pin 10. Install thrust ring A and locating pin C. Dec 2004 Issue 1 Section 1 Section 1 General Informatio n 2-1 2-1 Torque Torque Settings Use only where no torque setting is specified in the text.

Next

JCB 3DX Backhoe Loader Service Manual

jcb 3dx backhoe parts manual

Make sure that all pivot bores and pivot pins are clean and greased when assembling. Use extreme caution when driving onto ramps and trailers. Specifications all dimensions in mm Rivet Nut Thread Dia. Fit the first thin nut with zero torque, fit the second thin nut and torque to 98Nm 72 lbf ft. Check the condition of the brushes and, if necessary, clean the slip rings using extra-fine glass paper.

Next

JCB SERVICE MANUAL

jcb 3dx backhoe parts manual

Hold a piece of cardboard close to suspected leaks a nd then insp ect the cardboard for signs of hydraulic fluid. Switch off the engine and vent residual hydraulic pressure from the loader end by operating the loader controls back and forth several times. Keep a regular check on the hour meter readings to correctly gauge service intervals. Loosen the air vent screw A on the primary fuel filter as shown 2. It is important to note that excessive power washing can cause damage to the seals or bearings.

Next

JCB SERVICE MANUALS: JCB 3DX BACKHOE LOADER SERVICE REPAIR WORKSHOP MANUAL DOWNLOAD

jcb 3dx backhoe parts manual

The tyre mechanic should use a tyre inflation cage and the correct equipment to do the job. The grease must be a Modybdenium Disulphide or Check engine running Graphite no dropping andC. Fit the seal C and cover plate B. Put on initial charge at the appropriate current using direct current. If the fluid is cloudy, water or air has Water or air in the system could damage the hydraulic pump. Park the machine on level ground. To adjust the clearance, screw pad B fully in until it just touches the inner leg and then back the pad off by three quarter of a turn.

Next

JCB 3DX Backhoe Loader Workshop Service Repair Manual

jcb 3dx backhoe parts manual

If the diameter D2 at any point is less than that listed see table below , obtain a new tool. To avoid damage to the dipper or wear pad make sure the pads are fitted the correct way round as shown at J. Stop the engine, remove the starter key and r elieve system pressure. Note: To avoid excessive side loading on the steer valve, assemble the steering column 13, flexible coupling 26, extension shaft 24 and the steer valve with a minimum of misalignment before tightening securing bolts 11 and clamps 16 and 25. Place a container beneath the hydraulic tank to collect the oil, remove drain plug and drain the hydraulic tank.

Next

JCB 3DX, (India) Backhoe Loader Service Repair Workshop Manual

jcb 3dx backhoe parts manual

Readings should be taken using a hydrometer, when the electrolyte temperature is 15 0C 60 0F. If you begin to feel drowsy, stop the machine at once. Plug and cap all hose open ends to prevent ingress of dirt and loss of hydraulic fluid. Do not allow the knife blade to overheat or the sealant will melt. Open the discharge valve on the charging device. Measure the gap X which should be 1. If the battery capacity is shown as : Cold crank amps for 30 sec.

Next

JCB 3DX Backhoe Loader Workshop Service Repair Manual

jcb 3dx backhoe parts manual

The coupling bolt 25 must be engaged with the cut-out in the shaft, shown at B. Cover burns with a sterile dressing then get medical help. Make sure the step s , handrails and your boot soles are clean and dry. When connecting the battery, connect the earth - lead last. Park on level gro und. Remove the bolts securing the complete lever assembly to the chassis and withdraw the control levers and mounting bracket through the the electrical connector.

Next