The pressure point must be clearly perceptible. The adjusting screw is indexed and is easier Adjusting footbrake lever to turn if you push the hand- Make sure the ground is. There are four radial valves on each The raw numbers are enough to leave you in no doubt — this is a cylinder, with valve plate diameters of 39 millimetres at the in ow power unit that is built with absolute performance in mind. Press bulb socket 4 into the on left and right, but do not headlight housing. Lights up yellow warn- Electronic immobiliser active ing appears on the display. General warning light shows 0 °C, disengage the clutch after red. This must be roughened by Switch off the engine.
The possible warnings are listed on the next page. Subject to change in design and equipment. If necessary, slacken screws 1 and retighten screws 2 to the specified tightening torque. Tighten nut 2 in direction a to lock the adjuster. Warnings in text form alternate.
When changing the height of the motorcycle, always be sure to set the front and rear adjusters to the same settings. Two valves Turn adjusting screw until Always check that the tyre marks 1 are vertical. The lightweight rims are combined with from a state-of-the-art road-going sportsbike. The turn indicators are Telltale light for right-hand cancelled automatically turn indicator flashes. A defective bulb places Install the license-plate car-.
Position the rubber cap 1 on the headlight housing and push it into place. Adjusting mirrors Spring preload Setting It is essential to set spring pre- load of the rear suspension to suit the load carried by the mo- torcycle. If you prefer, you can use but- If you prefer, you can use but- ton 2 for this purpose. Check the clutch fluid level in If the pressure point is not clearly Clutch fluid level reservoir 1. Have the fault rectified as sufficient oil pressure is is- quickly as possible by a sued. Place the motorcycle on an ening torque.
Errors and omissions excep- ted. Remove bottom handlebar Position the handlebars clamping blocks 4. Replacing brake light and rear light bulb Remove the seat Remove screws 1. Remove wiring-harness end of plug 1 from the holder. Rebound stage, basic Compression stage, basic setting, rear setting, rear Turn adjusting screw as far Turn adjusting screw as far.
Make sure the ground is level and firm and place the motor- cycle on its stand. Tighten small screws 1 to the specified tightening torque. The keys exchange certain continuously Handlebars locked. The wires leading to the Jump-starting with a donor- power socket do not have battery voltage higher than a load-capacity rating adequate 12 V can damage the vehicle for jump-starting the engine. This must be Running in roughened by riding in a.
Brake system, general Checking brake function Damage to the engine Dependability of the Pull the handbrake lever. The hazard warning flashers continue to operate. Make sure the ground is level and firm and place the motor- cycle on its stand. Use rear-wheel stand with tool number 363980 with adapter shaft 363986 appropriate to the motorcycle. Push bulb 1 into socket 2.
Lights up yellow Fuel down to reserve warning appears on the display. This significantly re- duces braking efficiency. Setting for telescopic forks and spring strut for medium motorcycle height. Turn bulb 2 counter- position. Check temperature reduce air pressure accord- the air pressures before re- When the Air Damping Sys- ingly when the motorcycle is. Slacken right axle clamping Installing front-wheel stand screws 3. The erating temperature, make sure higher the temperature, the high- that the ground is level and er the level of oil in the sump.
You receive one master key and one spare key, plus a key for re- Switching off ignition moving the seat. If an electronic fuse trips and de-energises a circuit, the circuit is active as soon as the ignition is switched on after the fault has been rectified. Provides step-by-step instructions based on the complete disassembly of the machine. The pneumatic pump now has an airtight connection to the valve. Left and right turn indicator telltale lights are off. Attempting to adjust the Press and hold down Turn adjusting screw 1 clutch lever while riding button 1 until the reading counter-clockwise.