2005 pontiac g6 gt owners manual. Pontiac Pursuit 2005 2019-03-18

2005 pontiac g6 gt owners manual Rating: 6,2/10 1926 reviews

PONTIAC 2005 G6 OWNER'S MANUAL Pdf Download.

2005 pontiac g6 gt owners manual

Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. Tighten the M11 cylinder head bolts a second pass in sequence an additional 120 degrees using a angel meter. The belt is twisted across the body. You must do this before using the wheel wrench. Install the hydraulic element adjusters into their bores in the cylinder head.

Next

PONTIAC 2008 G6 OWNER'S MANUAL Pdf Download.

2005 pontiac g6 gt owners manual

Using the tool, rotate the tensioner clockwise in order to seat the tensioner pulley onto the drive belt. Disconnect the coolant temperature sensor. The exhaust push rods measure 6. Refer to the maintenance interval charts for the recommended replacement interval for the timing belt, and to the timing belt section for belt replacement and inspection. It includes indicator warning lights and gages that are explained on the following pages. Install the engine front cover. Remove the radiator inlet hose from the engine.

Next

2005 Pontiac G6 Factory Service Manual 2 Volume Set Original

2005 pontiac g6 gt owners manual

Nam tellus dolor, volutpat quis odio quis, vestibulum rutrum erat. The second glass panel will retract and the fourth glass panel will stack above the roof. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components. If the motor overheats due to heavy snow, etc. Raise the vehicle and remove the transaxle support. Remove the rear catalytic converter.

Next

2005 Pontiac G6 Factory Service Manual 2 Volume Set Original

2005 pontiac g6 gt owners manual

With the aid of an assistant, remove the cylinder head with the exhaust manifold. This, of course, disengages the cruise control. Move the seat rearward until it locks into place after the passenger enters the rear seat area. Windshield Washer To wash the windshield, press the button at the end of the lever until the washers begin. The nomenclature also hearkens back to the , another midsize car. Remove the engine from the engine stand.

Next

G6

2005 pontiac g6 gt owners manual

Use a remote positive + terminal if the vehicle has one. Remove the torque converter cover. Remove the engine mount bracket bolt and spacer. To help prevent the vehicle from moving: 1. That means better braking and longer brake life. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty.

Next

G6

2005 pontiac g6 gt owners manual

Remove the upper transaxle-to-engine bolts and the stud. Make sure that the inside surface of the rear window is not scratched and that the grid lines on the glass are not damaged. Page 9 Back to Top 2. This feature allows you to start the engine from outside of the vehicle. The shoulder belt may lock if you pull the belt across you very quickly. In a crash, this applies force to the strong pelvic bones. Exhaust pushrods are identified with green stripes and are 6 inches long.

Next

G6

2005 pontiac g6 gt owners manual

Install the flywheel and tighten the bolts to 52 ft. Maecenas feugiat sapien odio, nec imperdiet felis placerat pretium. Attach an engine lift hoist to the engine lift hooks. The current track will continue to repeat. A notice tells about something that can damage the vehicle. Separate and remove the upper intake manifold from the lower intake manifold. Towards the end of its life, the G6 was also offered with a 2.

Next

0 x Pontiac G6 Workshop & Owners Manual PDF's 2005

2005 pontiac g6 gt owners manual

Install the upper intake manifold gaskets. To play the song list, press the song list button. Disconnect the lower control arms from the steering knuckles. To install: Page 40 Back to Top Fig. This can usually be found where the hanging antenna wire is attached to the motor-head unit. Disconnect the outer tie rod ends from the steering knuckles. Connect the wiring harness electrical connector located at the side of the cylinder head.

Next